OwenDuffy.net |
|
The RB is prepared for configuration change by holding the PTT button down for at least two seconds when power is applied then releasing it.
PTT is again operated and the RB will pulse the transceivers PTT-OUT to the transceiver and a mode is selected by releasing the PTT switch during the appropriate pulse. After releasing PTT, wait for two seconds before pressing PTT again.
Pulse | Mode | Persistent | Comment |
1 | disable | YES | no tone is sent, but PTT is relayed |
2 | T | YES | single beep (Morse code T) |
3 | K | YES | Morse code K |
4 | V... | NO | PTT to activate and deactivate |
5 | continuous | NO | PTT to activate and deactivate |
6 | error | NO | restarts |
Chips shipped after 3 Jan 2008 are V1.03 or later
Pulse | Mode | Persistent | Comment |
1 | disable | YES | no tone is sent, but PTT is relayed |
2 | T | YES | single beep (Morse code T) |
3 | K | YES | Morse code K |
4 | E | YES | single beep (Morse code E) |
5 | V... | NO | PTT to activate and deactivate |
6 | continuous | NO | PTT to activate and deactivate |
Chips shipped after 21 Apr 2008 are V1.05 or later
Pulse | Mode | Persistent | Comment |
1 | disable | YES | no tone is sent, but PTT is relayed |
2 | T | YES | single beep (Morse code T) |
3 | K | YES | Morse code K |
4 | E | YES | single beep (Morse code E) |
5 | V... | NO | PTT to activate and deactivate |
6 | continuous | NO | PTT to activate and deactivate |
7 | set Morse code speed | YES | See below for setting Morse code speed |
Chips shipped after 10 May 2008 are V1.06 or later
Pulse | Mode | Persistent | Comment |
1 | disable | YES | no tone is sent, but PTT is relayed |
2 | T | YES | single beep (Morse code T) |
3 | K | YES | Morse code K |
4 | E | YES | single beep (Morse code E) |
5 | V... | NO | PTT to activate and deactivate |
6 | continuous | NO | PTT to activate and deactivate |
7 | set Morse code speed | YES | See below for setting Morse code speed |
8 | set TAPnYAP timeout (min) | YES | See below for setting TAPnYAP timeout |
Menu option 7 activates a sub menu for setting the Morse code speed. The speed can be set from 5WPM to 40WPM in increments of 5WPM, factory default is 20WPM. Close the PTT again and release it after one to eight pulses to set the Morse code speed. After releasing PTT, wait for two seconds before pressing PTT again.
Menu option 8 activates a sub menu for setting the TAPnYAP timout. The TAPnYAP timeout can be set from 0 to 10 increments of 2 minutes by selecting 1 to 11 pulses respectively. If the TAPnYAP timeout is set to 0 (1 pulse), TAPnYAP is disabled.
Chips shipped after 1 Nov 2008 are V1.07 or later.
Pulse | Mode | Persistent | Comment |
1 | disable | YES | no tone is sent, but PTT is relayed |
2 | T | YES | single beep (Morse code T) |
3 | K | YES | Morse code K |
4 | E | YES | single beep (Morse code E) |
5 | V... | NO | PTT to activate and deactivate |
6 | continuous | NO | PTT to activate and deactivate |
7 | woodpecker | NO | PTT to activate and deactivate |
8 | set Morse code speed | YES | See below for setting Morse code speed |
9 | set TAPnYAP timeout (min) | YES | See below for setting TAPnYAP timeout |
Menu option 8 activates a sub menu for setting the Morse code speed. The speed can be set from 5WPM to 40WPM in increments of 5WPM, factory default is 20WPM. Close the PTT again and release it after one to eight pulses to set the Morse code speed. After releasing PTT, wait for two seconds before pressing PTT again.
Menu option 9 activates a sub menu for setting the TAPnYAP timout. The TAPnYAP timeout can be set from 0 to 10 increments of 2 minutes by selecting 1 to 11 pulses respectively. If the TAPnYAP timeout is set to 0 (1 pulse), TAPnYAP is disabled.
Version | Date | Description |
1.01 | ||
1.02 | ||
1.03 |
© Copyright: Owen Duffy 1995, 2021. All rights reserved. Disclaimer.